Points Solar Radiation (Spatial Analyst)
Summary
Derives incoming solar radiation for specific locations in a point feature class or location table
Usage
-
The input locations can be a feature class or table. The table can be an INFO table, a .dbf file, an Access table, or a text table file.
-
When inputting locations by table, a list of locations must be specified with an x,y coordinate. Using a coordinate file, each line should contain an x,y pair separated by a space or tab. The following is an example:
X Y 325541.218750 4314768.5 325169.250000 4313907.0 325874.031250 4313134.0 325825.093750 4314181.5Alternatively, you may specify slope (degrees) and aspect in the location table. Along with the x,y coordinate, the file should contain the slope and aspect value for each location. The following is an example:
x y slope aspect 325541.218750 4314768.5 15.84516716 310.2363586 325169.250000 4313907.0 39.39801788 2.03503442 325874.031250 4313134.0 16.10847282 223.8308563 325825.093750 4314181.5 8.89850712 205.2011261 -
For multiday time configurations, the maximum range of days is a total of one year (365 days, or 366 days for leap years). If the start day is greater than the end day, the time calculations will proceed into the following year.
For example, [start day, end day] = [365, 31], represents December 31 to January 31 of the following year. For an example of [1, 2], the time is inclusive for the first day from 0:00 hours (January 1) to 0:00 (January 2). The start day and end day cannot be equal.
The year value for time configuration is used to determine a leap year. It does not have any other influence on the solar radiation analysis as the calculations are a function of the time period determined by Julian days.
-
For within-day time configurations, the maximum range of time is one day (24 hours). Calculations will not be performed across days (for instance, from 12:00 p.m. to 12:00 p.m. the next day). The start time must be less than the end time.
-
The use of a z-factor is essential for correcting calculations when the surface z units are expressed in units different from the ground x,y units. To get accurate results, the z units should be the same as the x,y ground units. If the units are are not the same, use a z-factor to convert z units to x,y units. For example, if your x,y units are meters and your z units are feet, you could specify a z-factor of 0.3048 to convert feet to meters.
-
It is recommended to have your data in a projection coordinate system (units meters). If you choose to run the analysis with a spherical coordinate system, you will need to specify an appropriate z-factor for that latitude. Following is a list of some appropriate z-factors to use if the x,y units are decimal degrees and the z units are meters:
Latitude Z-factor 0 0.00000898 10 0.00000912 20 0.00000956 30 0.00001036 40 0.00001171 50 0.00001395 60 0.00001792 70 0.00002619 80 0.00005156 -
The height offset should only be specified in meters.
-
The latitude for the site area (units: decimal degree, positive for the north hemisphere and negative for the south hemisphere) is used in calculations such as solar declination and solar position. Because the solar analysis is designed for landscape scales and local scales, it is acceptable to use one latitude value for the whole DEM. For broader geographic regions, it is necessary to divide the study area into zones with different latitudes.
-
For input surface rasters containing a spatial reference, the mean latitude is automatically calculated; otherwise, latitude will default to 45 degrees. When using an input layer, the spatial reference of the data frame is used.
-
Sky size is the resolution of the viewshed, sky map, and sun map rasters which are used in the radiation calculations (units: cells per side). These are upward-looking, hemispherical raster representations of the sky and do not have a geographic coordinate system. These grids are square (equal number of rows and columns).
Increasing the sky size increases calculation accuracy but also increases calculation time considerably.
-
When the day interval setting is small (for example, < 14 days), a larger sky size should be used. During analysis the sun map (determined by the sky size) is used to represent sun positions (tracks) for particular time periods to calculate direct radiation. With smaller day intervals, if the sky size resolution is not large enough, sun tracks may overlap, resulting in zero or lower radiation values for that track. Increasing the resolution provides a more accurate result.
-
The maximum sky size value is 10,000. A value of 200 is default and is sufficient for whole DEMs with large day intervals (for example, > 14 days). A sky size value of 512 is sufficient for calculations at point locations where calculation time is less of an issue. At smaller day intervals (for example, < 14 days), it is recommended to use higher values. For example, to calculate insolation for a location at the equator with day interval = 1, it is recommended to use a sky size of 2,800 or more.
-
Day intervals greater than 3 are recommended as sun tracks within three days typically overlap, depending on sky size and time of year. For calculations of the whole year with monthly interval, day interval is disabled and the program internally uses calendar month intervals. The default value is 14.
-
Because the viewshed calculation can be highly intensive, horizon angles are only traced for the number of calculation directions specified. Valid values must be multiples of 8 (8, 16, 24, 32, and so on). Typically, a value of 8 or 16 is adequate for areas with gentle topography, whereas a value of 32 is adequate for complex topography. The default value is 32.
-
The number of calculation directions needed is related to the resolution of the input DEM. Natural terrain at 30 meters resolution is usually quite smooth, so fewer directions are sufficient for most situations (16 or 32). With finer DEMs, and particularly with man-made structures incorporated in the DEMs, the number of directions needs to increase. Increasing the number of directions will increase accuracy but will also increase calculation time.
-
The Create outputs for each interval check box provides the flexibility to calculate insolation integrated over a specified time period or insolation for each interval in a time series. For example, for the within-day time period with an hour interval of one, checking this box will create hourly insolation values; otherwise, insolation integrated for the entire day is calculated.
-
The For each interval check box affects the number of attributes for output features. When checked for point radiation analysis, the output feature class includes additional attributes (t0, t1, t2, and so on), which indicate radiation or duration values for each time interval (hour interval when time configuration is less than one day, or day interval when multiple days).
-
The amount of solar radiation received by the surface is only a portion of what would be received outside the atmosphere. Transmittivity is a property of the atmosphere that is expressed as the ratio of the energy (averaged over all wavelengths) reaching the earth's surface to that which is received at the upper limit of the atmosphere (extraterrestrial). Values range from 0 (no transmission) to 1 (complete transmission). Typically observed values are 0.6 or 0.7 for very clear sky conditions and 0.5 for only a generally clear sky.
The value for the energy received at the earth's surface is at the shortest path through the atmosphere (that is, the sun is at the zenith, or directly overhead) and for sea level. For areas beyond Tropic of Capricorn and Tropic of Cancer, the sun can never be at the exact zenith, not even at noon; however, this value still refers to the moment when the sun is at the zenith. Because the algorithm corrects for elevation effects, transmittivity should always be given for sea level.
Transmittivity has an inverse relation with the diffuse proportion parameter.
Syntax
| Parameter | Explanation | Data Type |
in_surface_raster |
Input elevation surface raster. | Raster Layer |
in_points_feature_or_table |
The input point feature class or table specifying the locations to analyze solar radiation. | Feature Layer | Table View |
out_global_radiation_features |
The output feature class representing the global radiation or amount of incoming solar insolation (direct + diffuse) calculated for each location. The output has units of watt hours per square meter (WH/m2). | Feature Class |
height_offset (Optional) |
The height (in meters) above the DEM surface for which calculations are to be performed. The height offset will be applied to all input locations. | Double |
latitude (Optional) |
The latitude for the site area. The units are decimal degrees, with positive values for the northern hemisphere and negative for the southern. For input surface rasters containing a spatial reference, the mean latitude is automatically calculated; otherwise, latitude will default to 45 degrees. | Double |
sky_size (Optional) |
The resolution or sky size for the viewshed, sky map, and sun map grids. The units are cells. The default creates a raster of 200 by 200 cells. | Long |
time_configuration (Optional) |
Specifies the time configuration (period) used for calculating solar radiation. The Time class objects are used to specify the time configuration. The different types of time configurations available are TimeWithinDay, TimeMultiDays, TimeSpecialDays, and TimeWholeYear. The following are the forms:
The default time_configuration is TimeMultiDays with the start_day of 5 and end_day of 160, for the current Julian year. | Time configuration |
day_interval (Optional) |
The time interval through the year (units: days) used for calculation of sky sectors for the sun map. The default value is 14 (biweekly). | Long |
hour_interval (Optional) |
Time interval through the day (units: hours) used for calculation of sky sectors for sun maps. The default value is 0.5. | Double |
each_interval (Optional) |
Specifies whether to calculate a single total insolation value for all locations or multiple values for the specified hour and day interval.
| Boolean |
z_factor (Optional) |
The number of ground x,y units in one surface z unit. The z-factor adjusts the units of measure for the z units when they are different from the x,y units of the input surface. The z-values of the input surface are multiplied by the z-factor when calculating the final output surface. If the x,y units and z units are in the same units of measure, the z-factor is 1. This is the default. If the x,y units and z units are in different units of measure, the z-factor must be set to the appropriate factor, or the results will be incorrect. For example, if your z units are feet and your x,y units are meters, you would use a z-factor of 0.3048 to convert your z units from feet to meters (1 foot = 0.3048 meter). | Double |
slope_aspect_input_type (Optional) |
How slope and aspect information are derived for analysis.
| String |
calculation_directions (Optional) |
The number of azimuth directions used when calculating the viewshed. Valid values must be multiples of 8 (8, 16, 24, 32, and so on). The default value is 32 directions, which is adequate for complex topography. | Long |
zenith_divisions (Optional) |
The number of divisions used to create sky sectors in the sky map. The default is eight divisions (relative to zenith). Values must be greater than zero and less than half the sky size value. | Long |
azimuth_divisions (Optional) |
The number of divisions used to create sky sectors in the sky map. The default is eight divisions (relative to north). Valid values must be multiples of 8. Values must be greater than zero and less than 160. | Long |
diffuse_model_type (Optional) |
Type of diffuse radiation model.
| String |
diffuse_proportion (Optional) |
The proportion of global normal radiation flux that is diffuse. Values range from 0 to 1. This value should be set according to atmospheric conditions. The default value is 0.3 for generally clear sky conditions. | Double |
transmittivity (Optional) |
The fraction of radiation that passes through the atmosphere (averaged over all wavelengths). Values range from 0 (no transmission) to 1 (all transmission). The default is 0.5 for a generally clear sky. | Double |
out_direct_radiation_features (Optional) |
The output feature class representing the direct incoming solar radiation for each location. The output has units of watt hours per square meter (WH/m2). | Feature Class |
out_diffuse_radiation_features (Optional) |
The output feature class representing the incoming solar radiation for each location that is diffuse. The output has units of watt hours per square meter (WH/m2). | Feature Class |
out_direct_duration_features (Optional) |
The output feature class representing the duration of direct incoming solar radiation. The output has units of hours. | Feature Class |
Code Sample
The following Python Window script demonstrates how to use the PointsSolarRadiation tool.
import arcpy
from arcpy import env
from arcpy.sa import *
env.workspace = "C:/sapyexamples/data"
PointsSolarRadiation("elevation", "observers.shp",
"c:/sapyexamples/output/outglobalrad1.shp", "", 35, 200,
TimeMultipleDays(2009, 91, 212), 14, 0.5,"NOINTERVAL",
1, "FROM_DEM", 32, 8, 8,"STANDARD_OVERCAST_SKY", 0.3, 0.5,
"c:/sapyexamples/output/outdirectrad1.shp",
"c:/sapyexamples/output/outdiffuserad1.shp",
"c:/sapyexamples/output/outduration1.shp")
Calculate the amount of incoming solar radiation for specific point locations.
# PointsSolarRadiation_Example02.py
# Description: For all point locations, calculates total global, direct,
# diffuse and direct duration solar radiation for a whole year.
# Requirements: Spatial Analyst Extension
# Import system modules
import arcpy
from arcpy import env
from arcpy.sa import *
# Set environment settings
env.workspace = "C:/sapyexamples/data"
# Check out the ArcGIS Spatial Analyst extension license
arcpy.CheckOutExtension("Spatial")
# Set local variables
inRaster = "elevation"
inPntFC = "observers.shp"
outFeatures = "c:/sapyexamples/output/outglobal1.shp"
latitude = 35.75
skySize = 200
timeConfig = TimeMultipleDays(2009, 91, 212)
dayInterval = 14
hourInterval = 0.5
zFactor = 0.3048
calcDirections = 32
zenithDivisions = 8
azimuthDivisions = 8
diffuseProp = 0.3
transmittivity = 0.5
outDirectRad = "C:/sapyexamples/output/outdirectrad1.shp"
outDiffuseRad = "C:/sapyexamples/output/outdiffuserad1.shp"
outDirectDur = "C:/sapyexamples/output/outduration1.shp"
# Execute PointsSolarRadiation...
PointsSolarRadiation(inRaster, inPntFC, outFeatures, "", latitude, skySize,
timeConfig, dayInterval, hourInterval, "INTERVAL",
zFactor, "FROM_DEM", calcDirections, zenithDivisions,
azimuthDivisions,"STANDARD_OVERCAST_SKY", diffuseProp,
transmittivity, outDirectRad, outDiffuseRad, outDirectDur)